Skip to content
Plasma cutting & nesting
Studio

Shape Library

1,014 parametric plates. Pick one, set the sizes and send it straight to the Nesting Studio.

The shape library loads with JavaScript. If it does not appear, refresh the page or call us on 020 3633 8372 and we will draw your plate for you.

Browse all 1,014 parts as a list

Structural steelwork (101)

  • Base plate — Column base plate with n x m holding-down bolt grid, edge distance and corner radius.
  • Base plate, slotted holes — Base plate with slotted holes for site tolerance on holding-down bolts.
  • Column cap plate — Column cap plate with bolt holes for the beam over.
  • Beam end plate — Flush beam end plate: bolt rows down at gauge g and pitch p.
  • Moment connection plate — Extended moment end plate with top and bottom bolt groups, 2 or 4 bolts per row.
  • Fin plate — Fin plate: single line of bolts at distance ex from the free edge, optional top corner chamfer.
  • Web / flange stiffener — Partial-depth stiffener with corner snipes to clear the root radius.
  • Full-depth stiffener — Full-depth stiffener between flanges, snipes at both root corners.
  • Gusset plate — Right-angle gusset, chamfered toes, root snipe and bolt holes along each leg.
  • Knee brace gusset — Corner gusset with a raking edge leaving straight legs of depth b, bolt holes on each leg.
  • Haunch plate (tapered) — Tapered haunch web plate: depth h at the column face reducing to h2.
  • Flange splice plate — Flange cover plate with mirrored bolt groups each side of the joint.
  • Web splice plate — Web splice plate with vertical bolt rows each side of the joint.
  • Flat cleat — Flat bolted cleat with a bolt grid.
  • Shim / pack plate (slotted) — Packing shim with open U-slot(s) so it can be slid in around installed bolts.
  • Lifting lug — Lifting lug, radiused head with shackle pin hole, optional base bolt holes.
  • Padeye — Tapered padeye: wide base sweeping tangentially into a radiused head with pin hole.
  • Bearing plate — Bearing / spreader plate, plain or with fixing holes.
  • Purlin cleat — Purlin cleat with raked top corner and a pair of M12 purlin bolt holes.
  • Doubler / cranked plate — Doubler plate with corner chamfers and optional plug-weld hole grid.
  • Ring stiffener (CHS) — Annular ring stiffener for circular hollow sections.
  • CHS cap plate — Round end cap for a CHS post with a drain / vent hole.
  • Tie plate — Tie / strap plate with bolt groups at each end.
  • HD washer plate — Square holding-down washer plate with a centre hole (or slot) for HD bolts.
  • HD anchor plate — Cast-in anchor plate for the bottom of a holding-down bolt, centre hole plus optional corner holes.
  • Beam seating plate — Beam seating plate with slotted holes for adjustment.
  • Stair stringer end plate — Stringer end plate with the top edge raked to the stair pitch and a column of holes.
  • Stair tread fixing plate — Small fixing plate for stair treads with horizontal slots.
  • Sole plate — Long sole / wall plate with fixings at regular centres.
  • Kicker plate — Kicker / toe plate strip with slotted fixing holes.
  • Bracing gusset (slotted) — Bracing gusset with a raked corner and a slot along the brace line at angle a.
  • Edge protection post base — Post base plate with four fixing holes and a centre socket hole.
  • Column splice cover plate — Bolted column splice cover: flange or web cover plate for a UC serial size, two bolt groups either side of the joint gap.
  • Column division plate — Division plate between two columns at a bearing splice: rectangle with optional corner holes for erection cleats and a vent hole.
  • Bracing gusset, slotted — Corner bracing gusset (triangle with clipped corner) with bolt holes on two legs and slotted holes along the brace line for site adjustment.
  • Knee brace plate — Flat knee / fly-brace plate: a parallelogram strip with a bolt hole each end, angled ends square to the brace line.
  • Cap plate with drain holes — Hollow-section cap or base plate with corner drain / vent holes just inside the tube wall (for draining and venting) and optional bolt holes outside.
  • End plate with weld access — Partial-depth end plate with scalloped notches top and bottom for weld access, two vertical bolt lines at gauge g. Typical simple-connection proportions.
  • Fin plate, typical sizes — Single-line fin plate in typical simple-connection proportions: M20 8.8 bolts in 22 mm holes at 70 mm pitch, 50 mm end and 50 mm edge distances. Check against your connection design.
  • Partial end plate, typical — Partial-depth flexible end plate in typical proportions: 150 or 200 wide, M20 bolts in 22 holes, 90 or 140 cross centres, 70 pitch, 40 end distance. Check against your design.
  • Z purlin cleat (flat) — Flat blank for a Z purlin cleat: two rows of M12 purlin holes at the cleat top, slotted rafter fixings at the foot and an etched bend line for the cleat return.
  • C / Sigma purlin cleat — Cleat plate for C or Sigma section purlins: purlin holes in a pair at the top, slotted fixings to the rafter at the foot.
  • Side rail cleat — Side-rail (girt) cleat: tab welded or bolted to the column with two rail holes and a slotted column hole.
  • Sag rod / anti-sag plate — Small plate for anti-sag rods: angled rod holes at the chosen angle and fixing holes to the purlin or eaves beam.
  • Eaves beam cleat — Eaves beam cleat with a sloped top to the roof pitch, two beam holes and a column fixing pattern.
  • Horseshoe shim — Horseshoe (U) packer that slides round a bolt after the steel is up: rounded closed end and an open slot sized for the bolt.
  • Bearing / slip pad plate — Bearing or slip pad plate with slotted holes in one direction for thermal movement, and an etched centre cross for setting out.
  • Comb packer (twin slot) — Packer with two open slots (comb) so it slides past a pair of holding-down bolts; set the bolt centres and bolt size.
  • Portal apex plate — Apex connection end plate for a portal rafter: rectangle with paired bolt rows in the top and bottom zones.
  • Lintel / padstone plate — Spreader plate under a beam end on masonry: plain rectangle with optional fixing holes for resin anchors and an etched beam centre line.
  • Joist hanger flat blank — Flat pattern for a welded/folded timber joist hanger: cross-shaped blank with nail holes, the seat and side flaps marked by etched fold lines.
  • Rail clip plate — Rail clamp / clip plate: rectangle with a slotted bolt hole for adjustment and a stepped toe that bears on the rail foot.
  • Lacing / batten bar — Lacing bar for a laced or battened built-up member: flat bar with angled ends and one bolt hole (or none for welded) at each end.
  • Toe plate / kick strip — Toe plate strip for platforms and walkways: long flat with slotted fixing holes at the pitch you set and optional drainage notches along the bottom edge.
  • Ladder wall bracket — Fixed-ladder stand-off bracket: tapered arm with two wall fixing holes on the foot and two stile bolt holes at the tip.
  • Gutter support bracket — Flat gutter support bracket: L-shaped cradle with fixing holes in the back leg and a lip to hold the gutter edge.
  • Fly brace cleat — Small cleat that takes a fly brace off a purlin: tab with one round hole and one slotted hole set at the brace angle.
  • Notched web doubler — Supplementary web plate with corner notches to clear the root radii of the section, and optional bolt holes for plug or bolted fixing.
  • Wind post head plate — Wind-post head restraint plate with long vertical slots so the slab can deflect without loading the post.
  • Beam cope marking template — Thin marking template for cope / notch cuts on beam ends: L-shaped profile of the cope with a radiused internal corner to scribe round.
  • Base plate, bolts round the edge — Base plate with holding-down bolts spaced evenly round all four edges and an open centre: bolts per side, edge distance and hole size.
  • Base plate with grout and vent holes — Four-bolt base plate with a central grout-filling hole and small vent holes so grout can flow under the plate without air pockets.
  • Base plate with shear key slot — Base plate with a rectangular slot in the centre to take a welded shear key, plus four holding-down bolt holes.
  • Base plate with diagonal slots — Base plate with the four holding-down holes slotted towards the centre on the diagonals, for tolerance in both directions.
  • Lighting column base flange — Square base flange for a lighting column or pole: chamfered corners, four bolts on a PCD and a central cable entry hole.
  • Mast base flange, two bolt rings — Round base flange for a mast or pole with two concentric rings of bolts and a central opening.
  • Octagonal base plate — Octagonal base plate with bolts on a PCD and an optional centre hole, for poles and round columns.
  • Knife plate (tapered brace end) — Tapered plate that slots into the end of a tube brace: wide bolted end with a bolt group, narrowing to the welded end.
  • Skewed fin plate — Fin plate for a beam meeting the supporting member at an angle: parallelogram outline with one line of bolts.
  • Fin plate with flange notch — Fin plate with a rectangular notch in the bottom corner to clear the supporting beam flange.
  • Extended fin plate, two bolt lines — Long fin plate with two vertical lines of bolts for an extended connection.
  • Truss node gusset plate — Five-sided gusset for a truss node: bolt rows along the chord and two raking diagonal bolt groups.
  • Truss heel gusset — Heel gusset where a raking top chord meets the bottom chord: sloped top edge at the roof pitch, bolt rows on both members.
  • Saddle gusset for round tube — Gusset whose bottom edge is a concave arc so it sits on a round tube, with bolt holes in the upper part.
  • Bolted RHS splice flange — Square or rectangular end plate for a bolted hollow-section splice: bolts outside the tube on all four sides, tube outline etched.
  • Slotted tube end cap — End cap for a tube brace with a through-slot for a gusset plate to pass: square or round outline.
  • Box-section diaphragm plate — Internal diaphragm for a fabricated box section: corner snipes to clear the welds and a central access or lightening hole.
  • Web opening reinforcement plate — Plate that reinforces a service hole in a beam web: radiused rectangle with a matching round or rectangular opening.
  • Flitch plate — Long steel plate for a flitch beam between timbers: bolts staggered in two rows along the length, with end bearing zones clear.
  • Tie-rod wall bracket — Wall plate with a projecting lug and pin hole, cut as one piece, for canopy and glazing tie-rods.
  • Brickwork support bracket — Profile of a masonry support bracket: vertical back leg with a long slot for height adjustment, raking gusset and a toe to carry the support angle.
  • Balcony connection plate — End plate for a bolt-on balcony bracket: two columns of bolts top and bottom with a slotted shear location hole in the middle.
  • Floor plate panel with lifting holes — Removable floor or trench cover panel: radiused corners, two finger or key lifting holes and countersink-size fixing holes at the corners.
  • Grating fixing clip — Small clip plate that holds open-mesh grating down onto the steel: centre bolt hole and two hooked toes.
  • Cone / reducer flat pattern — Flat pattern for a truncated cone (concentric reducer or round hopper): large and small diameters and height; split into equal segments for big cones. Uses mean diameters, so enter them to the plate centre line.
  • Pyramid hopper side panel — One side of a square or rectangular pyramid hopper, drawn to its true slant height from the top size, outlet size and vertical height.
  • Tube saddle (fish-mouth) wrap template — Wrap-round template for marking the saddle cut where a branch tube meets a main tube at an angle: wrap the template round the branch and scribe along the curved edge. Cut it from thin sheet.
  • Lobster-back bend segment template — Wrap-round template for one middle segment of a segmented (lobster-back) bend: tube OD, bend radius and number of segments in 90°.
  • Auger / screw flight blank — Flat ring blank that is stretched into one turn of a screw conveyor flight: outside Ø, shaft Ø and pitch. The ring is cut through so it can be pulled out to the helix.
  • Cruciform base plate — Cross-shaped base plate for a cruciform or cross-stiffened column, with a holding-down bolt in each arm.
  • Corner column base plate — L-shaped base plate for a column at a building corner, with bolts kept away from the slab edges.
  • Beam hanger plate — Hanger plate for suspending a beam: a long plate with bolt groups at top and bottom.
  • Tapered cantilever end plate — Tapered end plate for a cantilever canopy beam, deeper at the top where the moment is.
  • Purlin sleeve splice plate — Flat splice plate for joining purlin lengths, with two bolt groups on standard gauge lines.
  • Dog-bone tie plate — Waisted tension tie plate with rounded ends and a bolt hole in each end.
  • Coped bearing stiffener — Bearing stiffener with corner snipes at both ends and a top cope to clear the flange weld.
  • Angle cleat flat blank — Developed flat blank for a pressed angle cleat, with the bend line etched and holes in both legs.
  • Spreader beam lug — Top lug for a spreader beam with a sling eye hole and a weld base.
  • Slab edge support bracket — Bracket plate supporting a slab edge trim, with slotted holes for line and level.
  • Deck closure strip — Long closure or edge trim strip with fixing holes at a set pitch, before folding.
  • Cellular beam cutting template — Template strip with a row of circular web openings at a set pitch, for marking or cutting cellular beam webs.

Architectural metalwork (100)

Engineering parts (98)

  • Flange — Plate flange: outside diameter, bore, bolt holes on a PCD.
  • Blind flange — Blind (blanking) flange, bolt holes on a PCD, no bore.
  • Gasket ring — Full-face gasket ring with bolt holes.
  • Washer / spacer ring — Plain washer or spacer ring.
  • Sprocket blank — Roller chain sprocket blank: teeth count and chain pitch, roller seat arcs approximated.
  • Spur gear blank — Spur gear blank with involute-approximated teeth (module m, z teeth, 20 degree pressure angle).
  • Pulley / sheave disc — Pulley or sheave web disc with bore, keyway and lightening holes.
  • Motor mount plate (slotted) — Motor base plate with slotted holes for belt tensioning and a shaft clearance hole.
  • Hinge plate — Hinge leaf blank with a radiused knuckle end, pin hole and countersink-ready fixing holes.
  • Clevis plate — Clevis / tang plate with a radiused pin end tapering to a wider fixed end.
  • Cam plate (eccentric) — Eccentric cam: circle of diameter d with the bore offset by e.
  • Keyhole hanger — Hanger plate with one or more keyhole slots.
  • D-shape plate — D-shape: rectangle with one semicircular end, optional centre hole.
  • Link plate (dog-bone) — Two-hole link plate with round lobes joined by a narrower waist.
  • Chain link oval — Flat oval chain link: obround outer with obround inner.
  • Bearing housing plate — Square bearing housing plate with centre bore and four corner holes.
  • Disc with lightening holes — Wheel / disc with a hub bore and a ring of lightening holes.
  • Bracket L-plate (flat blank) — Flat blank for a folded L bracket, holes on both legs, optional bend line etch.
  • T-blank — T-shaped blank with holes in the flange.
  • Flat bar with holes — Flat bar of length w and width h with n holes at pitch p (0 = spread between end distances).
  • Slotted bar — Flat bar with a row of slots.
  • Ratchet / star disc — Ratchet wheel with saw-tooth teeth and a centre bore.
  • Nameplate — Equipment nameplate / rating plate blank with rounded corners and fixing holes.
  • Slotted washer plate — Square plate washer with a slotted hole.
  • V-belt pulley side disc — Side disc for a fabricated V-belt pulley: outside Ø from the datum (pitch) Ø plus 2 × the groove top allowance for SPZ/SPA/SPB/A/B belts, bore and lightening holes.
  • Flexible coupling flange — Flange coupling half: disc with a keyed bore and a ring of pin / bolt holes; pair two for a rigid or pin-bush flexible coupling.
  • Split shaft collar blank — Flat split clamp collar: ring with a saw slot on one side and a clamp-screw boss hole across the split (drill and tap the cross hole after cutting).
  • Timing pulley flange — Thin guide flange for a timing pulley: ring with the pulley OD plus guide lip, centre bore and fixing screw holes.
  • Gear segment / quadrant — Toothed sector gear: teeth on an arc of the chosen angle (straight-flank approximation of the ISO 53 rack), pivot bore and two lightening holes.
  • Ratchet pawl — Pivoting pawl blank: lever with a pivot bore at one end, hooked tooth tip and a spring hole.
  • Cam / eccentric plate — Plate cam with a choice of profile (snail drop, single lobe, double lobe) defined by base radius and lift, bored for the shaft.
  • Geneva drive wheel — Geneva (Maltese cross) driven wheel: n radial slots for the drive pin and concave locking arcs between them, sized from the drive centre distance.
  • Spring anchor / tension plate — Tab with a row of spring hook holes for adjustable tension and two fixing holes.
  • Harrow / cultivator tine blank — Flat blank for a cultivator or harrow tine: long tapered blade with a pointed tip and two mounting holes at the root.
  • Bucket side cutter blank — Bolt-on side cutter / wear blade blank for a digger bucket: trapezoid with a bevel edge line etched and countersink-size bolt holes.
  • Three-point linkage plate — Linkage / headstock side plate with pin holes for Category 1 (19 mm), 2 (25.5 mm) or 3 (31.75 mm) top-link and lower-link pins.
  • Feed trough end plate — End plate for a rolled sheet trough: semicircular or V bottom with a lip, legs and fixing holes around the profile.
  • Hurdle / gate clip — Flat clip that joins two livestock hurdles: plate with two pin-hook slots open at the top.
  • Access / inspection cover — Bolted access cover: rectangle, round or obround with a ring of bolt holes at an even pitch round the edge and an optional lifting hole pair.
  • Hatch frame ring — Ring-shaped frame for an access opening: clear opening, frame width and bolt holes to match the access cover.
  • Louvre / vent panel — Ventilation panel with rows of long slots (press louvres after cutting, or leave as slots) and fixing holes in the border.
  • Fan guard grille — Round fan finger-guard: concentric ring slots separated by radial spokes, a central hub and corner or rim fixing holes.
  • Brush / cable entry plate — Cable entry plate with an obround cable slot (for a brush strip or grommet) and countersink-size fixing holes.
  • Earth / bus bar — Flat earth or bus bar with a row of tapped-size or clearance holes at a fixed pitch and two insulator mounting holes.
  • Enclosure wall-mount lug — Wall-mounting lug for enclosures and cabinets: L-shaped tab with a keyhole (or plain) wall slot and a screw hole to the enclosure, bend line etched.
  • Sheave / block cheek plate — Cheek plate for a pulley block: rounded plate with the sheave axle hole, a top shackle hole and two spacer-bolt holes. Not load rated.
  • Tank baffle plate — Internal baffle for a rectangular tank: corner flow notches, a manway hole and a pattern of flow holes.
  • Fan / mixer impeller blank — Flat impeller blank: hub with bore and n swept or straight blades (twist the blades after cutting for an axial fan or mixer).
  • Wear strip / skid plate — Bolt-on wear strip or liner with countersink-size bolt holes in one or two rows; use Hardox for abrasive duty.
  • Belt / chain guard panel — Side panel for a belt or chain drive guard: stadium outline round two pulleys at your centre distance, with a viewing mesh of small holes and fixing holes.
  • Lever arm (tapered) — Tapered lever with a large boss and bore at the pivot end and a smaller boss and hole at the other.
  • Bell crank (L lever) — Right-angled lever with a pivot hole at the corner and a hole at the end of each arm.
  • Triangular link plate — Three-hole triangular link with rounded corners, for linkages and suspension.
  • Rocker arm — Straight rocker with a large centre pivot boss and a hole at each end.
  • Connecting rod blank — Flat connecting-rod profile: big-end and small-end eyes joined by a tapered shank.
  • Torque arm — Reaction arm for a shaft-mounted gearbox: hub end with a ring of bolt holes, long arm and an anchor slot at the far end.
  • Pivot plate with curved slot — Quadrant plate with a pivot hole and a curved slot centred on it, for tilt or angle adjustment.
  • Belt tensioner arm — Arm with a pivot hole, an idler spindle hole and a curved locking slot round the pivot.
  • Cam clamp lever — Eccentric cam with an integral handle for quick-release clamps: the pivot hole is offset so the cam lobe tightens as the handle turns.
  • Heart cam (uniform motion) — Heart-shaped plate cam that gives the follower uniform rise and fall: base radius, lift and bore.
  • Clock escape wheel — Escape wheel with raked, pointed teeth and a spoked centre, for clocks and kinetic art.
  • Hinge leaf with knuckle tabs — Flat hinge leaf with alternating tabs along one edge to roll round a pin, and countersink-size fixing holes.
  • External retaining ring (circlip) — Flat external circlip for a shaft groove: open ring with two lugs and plier holes. Spring steel only; use as a pattern or for a one-off.
  • Internal retaining ring (circlip) — Flat internal circlip for a bore groove: open ring with two inward lugs and plier holes.
  • Tab washer — Washer with a long tab to bend up against a flat or into a hole and stop the nut turning.
  • Twin-nut locking plate — Plate that locks two bolt heads together: two bolt holes and bend-up tabs at both ends.
  • External-tooth lock washer — Washer with twisted-tooth pattern round the outside edge (cut flat; set the teeth after cutting).
  • Internal-tooth lock washer — Washer with teeth round the bore (cut flat; twist the teeth after cutting).
  • Anchor nut plate — Two-lug plate that carries a captive nut behind a panel: centre hole and two rivet holes in rounded lugs.
  • Disc with square bore — Disc or hub plate with a square bore to drive on a square shaft, and optional fixing holes.
  • Disc with hexagon bore — Disc with a hexagonal bore (across flats) to drive on a hex shaft or hold a nut.
  • Disc with double-D bore — Disc whose bore has two flats to drive on a double-D shaft.
  • Disc with splined bore — Disc with a straight-sided splined bore (blank for finishing): number of splines, minor and major diameters.
  • Spectacle blind — Figure-of-eight line blind: a solid blanking disc and an open spacer ring joined by a web, with bolt-clearance notches round both.
  • Paddle (spade) blind — Spade blank with a long handle for slipping between flanges; hole in the handle for an identification tag.
  • Orifice plate with handle — Flat orifice plate: disc to fit inside the flange bolts, a central bore (machine the edge after cutting) and a projecting tab for the data stamp.
  • Rectangular full-face gasket — Rectangular gasket with a rectangular opening and bolt holes at an even pitch round the frame.
  • Obround manway gasket — Obround (racetrack) gasket for a tank manway: inside opening, frame width and evenly spaced bolt holes.
  • Handwheel — Spoked handwheel: rim, hub with bore and three to six straight spokes.
  • Dividing (index) plate — Index plate with up to three concentric hole circles of different counts, for a dividing head or rotary table.
  • Castor top plate — Castor mounting plate with two common bolt patterns (slots cover both), and a centre hole for the swivel rivet.
  • Conveyor roller bracket — Side bracket that carries a conveyor roller spindle: drop-in hex or round slot open at the top and two fixing holes.
  • Pulley guard plate — Side plate for a two-pulley belt guard, shaped round both pulleys with fixing holes.
  • Chain guide plate — Long chain guide plate with a curved lead-in at each end and countersink fixing holes.
  • Square-to-round adaptor plate — Square adaptor plate with four corner holes and a ring of holes on a pitch circle round a centre bore.
  • Star knob blank — Lobed clamping knob blank with a hexagonal nut pocket hole in the centre.
  • T-handle blank — Flat T-handle with a round grip bar and a stem with a square drive hole.
  • Scissor link — Scissor lift link with end pivot holes and a centre pivot hole.
  • Toggle clamp arm — Clamp arm for a toggle clamp, with two pivot holes at the heel and a slot for the spindle at the nose.
  • Cylinder trunnion plate — Trunnion mounting plate for a hydraulic cylinder with a large pivot boss hole and four bolt holes.
  • Bearing retainer plate — Round bearing retainer with a shaft clearance bore and cap screws on a pitch circle.
  • Pump base plate — Base plate for a pump and motor set with slotted feet holes for alignment and four anchor holes.
  • Leaf spring blank — Flat spring leaf blank with tapered ends and a centre bolt hole.
  • Slewing ring adaptor ring — Ring plate with inner and outer bolt circles to adapt a slewing ring to its structure.
  • V-wheel gantry plate — Carriage plate for V-wheels on an aluminium extrusion rail: two fixed wheel holes, two eccentric spacer holes and a grid of tapped-hole positions for mounting.
  • Hook block cheek plate — Side cheek for a crane hook block: rounded top around the sheave pin hole and a lower hole for the hook crosshead.
  • Beam trolley side plate — Side plate for a push beam trolley: two wheel axle holes near the top and a load pin hole below the centre.
  • Cable drum flange — Flange disc for a cable or hose drum with a centre arbor hole, a drive pin hole and lightening cut-outs.

Geometric shapes (136)

  • Rectangle — Plain rectangular plate.
  • Square — Plain square plate.
  • Rounded rectangle — Rectangle with radiused corners.
  • Chamfered rectangle — Rectangle with chamfered (cropped) corners.
  • Circle / disc — Solid disc, optional centre hole.
  • Ring / annulus — Annular ring.
  • Ellipse — Ellipse of width w and height h.
  • Regular polygon — Regular polygon with n sides, sized across flats or across corners.
  • Hexagon — Regular hexagon, sized across flats or corners.
  • Octagon — Regular octagon.
  • Triangle — Triangle from three side lengths (a = base), or right-angled from base and height.
  • Isosceles trapezium — Isosceles trapezium: bottom width w, top width w2, height h.
  • Parallelogram — Parallelogram: base w, height h, horizontal offset s.
  • Rhombus / diamond — Rhombus from its two diagonals.
  • L-shape — L-shaped plate with leg widths a (vertical leg) and b (horizontal leg).
  • T-shape — T-shaped plate: flange depth tf at top, stem width tw.
  • U-shape — U-shaped plate: legs of width a, base depth b.
  • Z-shape — Z-shaped plate: top and bottom flanges of depth t joined by a web of width t.
  • Cross / plus — Cross / plus shape with arm width t.
  • Star — Star with n points, outer and inner radius.
  • Chevron — Chevron (V stripe) of overall width w, height h and bar thickness t.
  • Arrow — Arrow: shaft width sw, head length hl, overall w x h.
  • Semicircle — Half disc of diameter d.
  • Sector — Circular sector of radius r and included angle a.
  • Annular sector — Curved plate: annular sector between inner and outer radii over angle a.
  • Circular segment — Circular segment: chord length w and rise h.
  • Slot / obround — Obround (full radius ends).
  • Stadium (two holes) — Stadium plate with a hole in each end.
  • Crescent — Crescent: outer disc minus an offset inner disc.
  • Heart — Heart shape of overall width w.
  • D-shape — D-shape: rectangle with a semicircular end.
  • Rounded triangle — Equilateral triangle with radiused corners.
  • Quarter circle — Quadrant of radius r.
  • Rounded regular polygon — Regular polygon with every corner radiused: number of sides, size across corners and corner radius.
  • Reuleaux triangle — Curve of constant width built from three arcs: every width across it is the same.
  • Reuleaux polygon (5, 7 or 9 sides) — Odd-sided curve of constant width, like a seven-sided coin.
  • Superellipse — Lamé curve between an ellipse and a rectangle: width, height and squareness exponent.
  • Squircle — Square with continuously curving sides, softer than a radiused square.
  • Concave-sided square (astroid) — Four-pointed shape with inward-curving sides; the curve depth sets how pinched it is.
  • Cardioid (heart curve) — Smooth heart-like curve with one dimple, as traced by a point on a rolling circle.
  • Dimpled oval (limaçon) — Oval with a shallow dimple on one side.
  • Flower, n petals — Rounded flower outline with a chosen number of petals and petal depth.
  • Scalloped-edge disc — Disc whose edge is a ring of round scallops meeting in points.
  • Castellated disc — Disc with square notches cut round the edge, like a castellated nut or a crown.
  • Wavy-edged disc — Disc with a smooth wavy edge: number of waves and wave height.
  • Cloud — Cloud outline: flat base and a row of round puffs on top.
  • Teardrop — Teardrop outline: round base and a pointed tip; size and tip length.
  • Egg shape — Egg outline, fuller at the base than the top.
  • Four-centre oval — Classic four-arc (four-centre) oval as drawn by architects and joiners, smoother than a racetrack.
  • Lens (vesica) — Pointed lens made of two circular arcs: length and width.
  • Kite — Kite quadrilateral: width, height and where the cross-piece sits.
  • Right-angled trapezium — Four-sided plate with two right angles and one sloping side: bottom width, top width and height.
  • House shape (gable) — Rectangle with a pitched roof: width, wall height and roof pitch.
  • Heater shield — Classic heraldic shield: flat top, straight sides curving to a point.
  • Shield, rounded base — Shield outline with a flat top and a semicircular base.
  • Gothic (pointed) arch panel — Panel with a pointed Gothic arch top: width, side height and arch sharpness.
  • Ogee arch panel — Panel with an ogee (S-curve) arch rising to a point.
  • Double-headed arrow — Arrow with a head at each end: length, head width and shaft width.
  • Curved arrow — Arrow bent round a curve: radius, sweep angle and band width.
  • Lightning bolt — Zig-zag lightning bolt outline.
  • Speech bubble — Rounded rectangle with a pointed tail at the bottom left.
  • Speech bubble, round — Elliptical speech bubble with a curved tail.
  • Jigsaw puzzle piece — Square jigsaw piece with two knobs out and two sockets in.
  • Maltese cross — Eight-pointed cross of four flared, notched arms.
  • Latin cross — Cross with a longer lower arm: height, arm span and bar width.
  • Cross pattée — Cross with arms that flare out from a narrow centre.
  • Celtic cross — Cross with a ring round the crossing; the four gaps inside the ring are cut out.
  • Rounded-end cross — Plus-shaped cross with fully rounded arm ends.
  • Sun with rays — Disc with separate triangular rays joined at their base: number and length of rays.
  • Star with rounded points — Star outline with radiused points and valleys.
  • Decorative cog — Cog wheel outline with trapezoid teeth for signs and decoration (not a working gear).
  • Hourglass / bow tie — Two triangles meeting at a waist: width, height and waist width.
  • Elongated hexagon — Hexagon stretched to a length with pointed ends.
  • Elongated octagon — Rectangle with equal clipped corners making a stretched octagon.
  • Figure-eight plate — Two overlapping discs joined at a waist, each with its own hole.
  • Peanut (Cassini oval) — Smoothly waisted oval: length and how deep the waist is.
  • Disc with two flats — Circular disc with two parallel flats: diameter and size across the flats.
  • Curved bar (arc strip) — Bar bent to a radius with rounded ends: radius, sweep and width.
  • Plate with semicircular edge notch — Rectangle with a round notch in one long edge, for a pipe or cable to pass.
  • Plate with V notch — Rectangle with a V-shaped notch in one edge: notch width and depth.
  • Fork / open-slot end plate — Plate with an open round-ended slot from one end, like a fork end.
  • Ticket shape — Rectangle with a round bite out of each corner, like a ticket.
  • Semi-ellipse — Half an ellipse on a straight base: base width and height.
  • Parabolic segment — Area under a parabola on a straight base: base width and height.
  • Square frame — Square frame of equal width all round.
  • Rectangular frame — Rectangular frame of equal width all round.
  • Rounded rectangular frame — Rectangular frame with radiused corners inside and out.
  • Hexagonal frame — Hexagon with a hexagonal window.
  • Octagonal frame — Octagon with an octagonal window.
  • Triangular frame — Equilateral triangle with a triangular window.
  • Star frame — Five-pointed star with a star-shaped window.
  • Heart frame — Heart outline with a heart-shaped window.
  • Diamond frame — Diamond (rhombus) with a matching window.
  • Oval frame — Elliptical frame of equal-looking width.
  • Arched frame — Round-topped panel with a matching round-topped window.
  • H shape — H-shaped plate: width, height, leg width and bar width.
  • E shape — E-shaped plate with three arms: width, height, spine and arm widths.
  • F shape — F-shaped plate: width, height, spine and arm widths.
  • Open ring (C shape) — Ring with a gap cut through one side: outside and inside diameters and gap width.
  • I-section profile template — Flat I-section outline with root radii: depth, flange width, web and flange thickness. For blanking plates, templates and signs.
  • Wave strip — Strip of even width with rounded ends that follows a sine wave: length, wave height, number of waves and strip width.
  • Zig-zag strip — Strip of even width that zig-zags: length, zig-zag height, number of peaks and strip width.
  • Castellated strip — Strip with square teeth along one edge: length, height, tooth count and tooth height.
  • Comb strip — Strip with long narrow fingers along one edge.
  • Sawtooth strip — Strip with sloping saw teeth along one edge.
  • Plate with one wavy edge — Rectangle whose top edge is a smooth wave.
  • Plate with scalloped edge — Rectangle with a row of round scallops along the bottom edge, like a canopy valance.
  • Plate with square notched corners — Rectangle with a square notch cut from each corner, as for a folded tray.
  • Bar with pointed end — Flat bar with a symmetrical point at one end: length, width and point length.
  • Fishtail-ended bar — Flat bar with a V cut into one end, as for a building-in holdfast.
  • Bar with one rounded end — Flat bar with a fully rounded end and a square end.
  • Tapered bar — Flat bar that tapers from one width to another along its length.
  • Spiral strip — Flat spiral of even width: number of turns, gap between turns and strip width.
  • Trefoil — Solid three-lobed Gothic trefoil.
  • Quatrefoil — Solid four-lobed Gothic quatrefoil.
  • Cinquefoil — Solid five-lobed Gothic cinquefoil.
  • Tetromino block — One of the seven four-square puzzle blocks: I, O, T, S, Z, L or J.
  • Arrow with notched tail — Arrow with a pointed head and a swallow-tail notch at the back.
  • Double chevron — Two nested chevrons joined into one piece by a thin web.
  • Interlaced triangles frame — Two triangular frames laid over each other into a six-pointed star outline.
  • Scallop shell — Fan-shaped scallop shell with radiating rib slots and a hinge base.
  • Disc with spiral slot — Round disc with one continuous spiral slot cut into it.
  • Kidney bean — Smooth kidney-bean outline: a soft oval with one inward curve.
  • Isometric cube — Hexagon divided into three rhombus cut-outs so it reads as a cube.
  • Infinity loop — Infinity symbol cut as a band with two open loops.
  • Three linked rings — Three overlapping rings in a row, cut as one piece.
  • Triquetra knot — Three interlaced pointed loops (triquetra), cut as one band.
  • Seed of life — Seven overlapping circles drawn as bands inside an outer ring.
  • Moon and star — Crescent moon with a star in its curve, joined by a bridge.
  • Circular arrows — Two curved arrows chasing each other round a circle, joined at the centre.
  • Keyhole — Solid keyhole shape: a round head on a tapered tail.
  • Octagram (eight-point star) — Eight-pointed star made from two overlapping squares.
  • Half ring — Half of a flat ring, with square ends.
  • Ring with tabs — Flat ring with square tabs projecting outward, each with an optional hole.
  • Pentagon frame — Regular pentagon with a pentagon cut out, leaving an even border.
  • Arrowhead — Arrowhead with a notched back, like the tip of an arrow.

Standard flanges and washers (42)

  • EN 1092-1 PN6 plate flange — Type 01 plate (slip-on) flange to BS EN 1092-1 PN6: OD, PCD, bolt holes and bore B1 from the standard table.
  • EN 1092-1 PN6 blind flange — Type 05 blind (blanking) flange to BS EN 1092-1 PN6: OD, PCD and bolt holes from the standard table, no bore.
  • EN 1092-1 PN10 plate flange — Type 01 plate (slip-on) flange to BS EN 1092-1 PN10: OD, PCD, bolt holes and bore B1 from the standard table.
  • EN 1092-1 PN10 blind flange — Type 05 blind (blanking) flange to BS EN 1092-1 PN10: OD, PCD and bolt holes from the standard table, no bore.
  • EN 1092-1 PN16 plate flange — Type 01 plate (slip-on) flange to BS EN 1092-1 PN16: OD, PCD, bolt holes and bore B1 from the standard table.
  • EN 1092-1 PN16 blind flange — Type 05 blind (blanking) flange to BS EN 1092-1 PN16: OD, PCD and bolt holes from the standard table, no bore.
  • ASME B16.5 Class 150 flange — ASME B16.5 Class 150 slip-on flange outline: OD, bolt circle, holes and bore from the standard (inches converted to mm).
  • ASME B16.5 Class 150 blind — ASME B16.5 Class 150 blind flange outline: OD, bolt circle and holes, no bore.
  • Class 150 ring gasket (flat) — Flat inside-bolt-circle ring gasket blank for a Class 150 joint: OD sits just inside the bolts, ID equals the slip-on bore.
  • ISO 7089 plain washer — Normal-series plain washer to ISO 7089: inside and outside diameters from the table (the h column is the standard thickness to order).
  • ISO 7093 large washer — Large-series washer to ISO 7093-1 (about 3 x bolt Ø outside): diameters from the table.
  • HD square plate washer — Square holding-down plate washer: common UK workshop sizes by bolt, hole = bolt + 2 or + 3 mm clearance (EN ISO 20273 medium).
  • ISO 606 sprocket plate — Plate sprocket for ISO 606 (BS) roller chain: pick the chain, set the teeth. Tooth form is a seat-arc approximation, finish-machine for high speed.
  • NEMA stepper motor plate — Stepper motor mounting plate: NEMA face hole square and pilot hole, plus corner fixing holes or slots to your frame.
  • IEC motor base plate — Base plate for a foot-mounted (B3) IEC motor: the A x B foot hole pattern for the frame size, plus slotted fixings for belt adjustment.
  • VESA mount plate — Screen mounting plate with the VESA hole square, optional nested smaller patterns and a cable / fixing hole set.
  • 19 inch rack panel — 19 inch rack front panel to EIA-310: 482.6 mm wide, n x 44.45 mm high (less 0.8 mm), mounting slots at 465.1 mm centres.
  • DIN rail backplate — Control panel mounting plate with rows of tapped-size holes for 35 mm TS35 rails (EN 60715) and corner fixing holes.
  • Cable gland plate — Enclosure gland plate: rows of metric cable-gland clearance holes (M16 to M63, EN 62444 thread sizes) with corner fixings.
  • EN 1092-1 PN25 plate flange — Type 01 plate flange to BS EN 1092-1 PN25: OD, PCD, bolt holes and bore B1 from the standard table.
  • EN 1092-1 PN25 blind flange — Type 05 blind flange to BS EN 1092-1 PN25: OD, PCD and bolt holes from the table, no bore.
  • EN 1092-1 PN40 plate flange — Type 01 plate flange to BS EN 1092-1 PN40: OD, PCD, bolt holes and bore B1 from the standard table.
  • EN 1092-1 PN40 blind flange — Type 05 blind flange to BS EN 1092-1 PN40: OD, PCD and bolt holes from the table, no bore.
  • BS 10 Table D flange — Plate flange to BS 10 Table D (inch OD and PCD converted to mm, metric bolt clearance holes, bore = steel pipe OD + 1.5 mm).
  • BS 10 Table D blind — Blind (blanking) flange drilled to BS 10 Table D, no bore.
  • BS 10 Table E flange — Plate flange to BS 10 Table E (inch OD and PCD converted to mm, metric bolt clearance holes, bore = steel pipe OD + 1.5 mm).
  • BS 10 Table E blind — Blind (blanking) flange drilled to BS 10 Table E, no bore.
  • IEC B5 motor adaptor plate — Square adaptor plate to take a B5 (FF) flange motor: spigot bore N + clearance, 4 holes Ø S on PCD M, corner fixings to your frame.
  • IEC B14 motor face plate — Plate to bolt a B14 (FT) face motor from behind: spigot bore N, 4 clearance holes for the face threads on PCD M, corner fixings.
  • UCF 4-bolt bearing plate — Mounting plate for a 4-bolt square UCF flange bearing: bolt square J, shaft clearance hole, plate margin and corner fixings.
  • UCFL 2-bolt bearing plate — Mounting plate for a 2-bolt oval UCFL flange bearing: bolt centres J, shaft clearance hole and optional slotted holes for alignment.
  • Keyed hub disc (DIN 6885) — Disc with a shaft bore and the hub keyway sized automatically from DIN 6885-1 for that shaft (width b, hub depth t2), plus optional bolt circle.
  • Gear rack strip — Straight gear rack by module to the ISO 53 basic rack (20° pressure angle, addendum 1 m, dedendum 1.25 m) with fixing holes in the body.
  • Internal ring gear blank — Internal (annulus) gear profile by module and teeth on an outer ring with bolt holes; straight-flank approximation, finish-machine for drives.
  • Flat spanner blank — Flat open-ended spanner blank sized for an ISO 4032 nut across flats, 15 degree jaw, with a hanging hole. Harden and finish for heavy use.
  • Hex nut trap plate — Plate with hexagon cut-outs that hold ISO 4032 nuts from turning (across flats + clearance), in a row or grid.
  • Column base plate (UC / UB) — Base plate sized from the column section (BS 4-1 serial size) plus an overhang, 4 or 6 holding-down holes outside the flanges and a grout hole.
  • CHS post base plate — Square or round base plate for a circular hollow section (EN 10219 outside diameters) with the tube outline etched, a vent hole and 4 fixings.
  • SHS post base plate — Base plate for a square hollow section post: outline etched for setting out, central vent, 4 corner holes or 2 side holes.
  • HD bolt setting-out template — Thin template that holds cast-in holding-down bolts at the right centres while concrete is poured: bolt holes, etched grid lines and a pour hole.
  • ASME B16.5 Class 300 flange — ASME B16.5 Class 300 slip-on flange outline: OD, bolt circle, holes and bore from the standard (inches converted to mm).
  • ASME B16.5 Class 300 blind — ASME B16.5 Class 300 blind flange outline: OD, bolt circle and holes, no bore.

Automotive and trailer (49)

  • Number plate backing bracket — Steel backing bracket for UK registration plate sizes (520 x 111, 280 x 203, 229 x 178, 330 x 111): plate fixing holes plus a mounting tab with slots.
  • D-ring / lashing plate — Base plate for a weld-on or bolt-on lashing D-ring: rounded rectangle with a centre slot for the ring keeper and four fixing holes. Not load rated: a cut blank only.
  • Tow bracket side plate — Flat tow-bracket / drop plate blank: tall plate with a vertical row of 50 mm-flange towball hole pairs (90 mm × 2 bolt, 17 mm holes) for height adjustment. Not load rated: a cut blank only.
  • Mudguard / wing bracket — Trailer mudguard stay: L-shaped flat bracket with slotted holes on the axle end for adjustment and holes for the guard.
  • U-bolt / axle clamp plate — Clamp plate for a pair of U-bolts: four holes at the U-bolt centres and optional centre-bolt hole for leaf springs.
  • Trailer lamp bracket — Rear lamp mounting plate with a cable hole, two lamp stud holes at your centres and two chassis fixing slots.
  • Jockey wheel clamp plate — Pair-of-plates blank for a jockey-wheel clamp: plate with the tube bore and two clamp bolt holes beside it.
  • Exhaust hanger bracket — Exhaust hanger plate: rubber-mount pin hole at the end of a tapered arm, two chassis fixing holes at the base.
  • Battery hold-down bar — Battery clamp bar with J-bolt slots at each end to suit battery widths, and an optional lightening slot.
  • Roof bar / rack foot plate — Foot plate for a roof rack leg: plate with gutter-clamp or rail bolt slots and a tube outline etched for welding.
  • Recovery point plate — Recovery-point style plate: rounded lug with a shackle pin hole and chassis bolt holes in the base. Not load rated: a cut blank only.
  • Steering boss / PCD adaptor — Adaptor disc for steering wheels: outer 6-hole pattern (70 mm common motorsport PCD) and an inner pattern of your choice with a centre bore.
  • Wheel PCD template / spacer blank — Disc drilled to a wheel stud pattern (e.g. 4×100, 5×112, 5×120, 6×139.7) with a hub bore; use as a template or spacer blank. Not load rated: a cut blank only.
  • Exhaust flange, 2-bolt — Two-bolt oval (diamond) exhaust flange with the pipe bore in the middle.
  • Exhaust flange, 3-bolt — Three-bolt triangular exhaust flange with radiused corners and a pipe bore.
  • Turbo / manifold flange, 4-bolt — Four-bolt flange with a rectangular (or round) port and radiused corners, set your own bolt pattern.
  • Winch mounting plate — Winch mounting plate with a four-bolt winch foot pattern (254 × 114.3 mm is common) and a fairlead pattern in front.
  • Leaf-spring hanger plate — Hanger side plate for a leaf-spring eye: tapered plate with the eye bolt hole and chassis weld edge.
  • Chassis gusset with lightening holes — Triangular chassis gusset with clipped corners and round lightening holes.
  • Crossmember end plate — Bolt-on end plate for a box-section crossmember: rectangle with four bolts round the tube outline (etched).
  • Bumper mounting bracket — Flat bumper bracket: chassis end with slotted holes for adjustment and a bumper end with two holes.
  • Mudflap bracket — L-shaped flat mudflap bracket with chassis slots on the short leg and flap holes along the long leg.
  • Rope tie cleat plate — Flat rope hook plate for a trailer side: two hooks to loop rope round and fixing holes.
  • Tow ball mounting plate — Drop plate for a two-bolt tow ball (90 mm centres is common) with a choice of heights.
  • Spare wheel carrier plate — Plate that carries a spare wheel on its studs: wheel PCD holes, centre bore and four mounting holes.
  • Roll-cage tube gusset — Gusset for a tube joint in a roll cage: two straight legs joined by a concave quarter-circle edge.
  • Seat mounting plate — Flat seat-mounting plate with a slotted row for fore-and-aft adjustment and floor bolt holes.
  • Engine mount plate — Engine mount adaptor plate: block bolt holes in an arc at one end, mount slot pair at the other.
  • Brake caliper bracket blank — Blank for a brake caliper adaptor: hub mounting holes on one side, caliper bolt holes on the other, with an arc inner edge to clear the hub.
  • Battery tray blank — Flat blank for a folded battery tray: corner notches, drain holes and hold-down slots.
  • Light bar bracket — Flat L bracket for a light bar or spot lamp: slotted base and a pivot hole with an arc slot for the angle.
  • Sump guard / skid plate — Underbody protection plate with drain or access holes, lightening slots and mounting holes round the edge.
  • Dashboard switch panel — Switch panel with a row (or two) of round holes for toggle or push switches and corner screw holes.
  • Gauge panel — Instrument plate with holes for 52 mm (or other size) gauges in a row.
  • Alternator bracket — Alternator adjusting bracket with a curved tension slot and pivot hole.
  • Radiator mounting bracket — Radiator mounting bracket with a rubber bush hole and two chassis fixing holes.
  • Fuel tank strap end — Strap end for a fuel tank: a long strap with a hooked eye and a bolt slot for tensioning.
  • Shock absorber mount plate — Shock absorber mount ear: round top with the eye bolt hole and a wide weld base.
  • Panhard rod bracket — Triangulated Panhard rod bracket with three height-adjustment holes.
  • Jacking point plate — Jacking point reinforcement plate with a locating hole and lightening slots.
  • Towbar socket plate — Towbar electrics socket plate: round boss with the socket hole and three fixing holes, on a mounting tab.
  • Gear shifter gate plate — Gated shifter plate with an H-pattern gate cut as one slot and four fixing holes.
  • Pedal box plate — Pedal box side plate with pivot holes for three pedals and master cylinder mounting holes.
  • Coilover spring seat — Spring seat ring for a coilover, with a body bore and optional notches for a C-spanner.
  • Bonnet pin plate — Oval bonnet pin plate with the pin hole and two rivet holes.
  • Trailer A-frame hitch plate — Triangular plate for the nose of a trailer A-frame, with coupling bolt holes.
  • Wheel chock plate — Wheel chock side profile with a curved face and a base flange with bolt holes.
  • Loading ramp hook plate — Ramp end plate with a hooked lip that drops over a tailgate or trailer bed.
  • Intercooler bracket — Dog-leg intercooler bracket with slotted holes at both ends.

Signage and lettering (51)

  • Lettering stencil plate — Spray-paint stencil: your text cut through in the PSS stencil font with bridges so letter centres stay in. Plate size follows the text.
  • House number plate — House or unit number cut through a plate (with stencil bridges) in a rectangle, oval, arched or chamfered outline, with fixing holes.
  • House name sign (two lines) — House or farm name sign with a main line and a smaller second line, both cut through with bridges, arched or square top and hanging holes.
  • Word on a rail (solid letters) — Solid letters standing on a bar (letters are the steel), for gate toppers, wall words and shop names. Fixing holes in the rail.
  • Freestanding letter or number — One solid letter or number with rounded strokes, for wall initials, workshop numbering or 3D signage faces.
  • Monogram disc — Round plaque with up to three initials cut through (bridged), an optional border ring etched and a hanging hole.
  • Direction arrow sign — Pointer sign shaped as an arrow with your word cut through the body, for yards, car parks and finger posts.
  • Etched text plaque — Plate with up to two lines of text etch-marked (not cut) by the torch, an etched border and countersink-sized fixing holes.
  • Valve / asset ID tag — Round equipment ID disc with a wire hole and the tag number etched, for valves, pipework and plant.
  • Key / locker tag — Rounded-end tag with a key ring hole and an etched number or name.
  • Bone-shaped pet tag — Dog-bone tag with a ring hole and the pet name etched.
  • Desk name plate (fold) — Flat blank for a folded desk plate: name cut through the front face (bridged), fold lines etched for the press brake.
  • Triangular sign blank — Equilateral triangular sign blank (side measured to the sharp corners) with radiused corners and fixing holes on the centre line for post clips or banding.
  • Circular sign blank — Round sign blank with two fixing holes on the vertical centre line and an optional etched inner ring for the border.
  • Octagonal sign blank — Regular octagon sign blank (flat top) sized across flats, with radiused corners and centre-line fixing holes.
  • Rectangular sign blank — Rectangular sign blank with radiused corners and pairs of fixing holes or clip slots for one or two posts.
  • Shield sign blank — Heraldic shield sign blank with an etched border and two fixing holes.
  • Arched-top sign blank — Rectangular sign blank with a segmental arched top.
  • Oval sign blank — Oval sign or plaque blank with an etched border.
  • Ribbon banner sign — Banner-shaped sign with swallowtail notches at both ends.
  • Scroll-ended plaque — Plaque with rolled-scroll ends at left and right.
  • Hanging sign with top lugs — Sign blank with two rounded lugs on top for chains or rings.
  • Fingerpost sign blade — Pointed fingerpost blade for a signpost, with fixing holes at the square end.
  • Street name plate — Long street-name plate with radiused corners, an etched border and four fixing holes.
  • Diamond hazard sign blank — Square sign set on its point, for hazard diamonds and warning labels.
  • Post-mounted sign with band slots — Sign plate with two pairs of slots for steel banding or ties round a post.
  • Projecting flag sign — Sign blade with a wall-fixing tab along one side, for projecting signs.
  • A-board sign panel — Panel for a pavement A-board: hand-hold slot at the top and hinge holes.
  • Bunting pennant — Triangular pennant with two holes along the top for stringing.
  • Plaque with mitred corners — Rectangular plaque with chamfered (mitred) corners and an etched border.
  • Keyhole-hung plaque — Plaque that hangs on screws through two keyhole slots near the top.
  • Luggage / gift tag — Tag with a clipped end and a hole for a cord or ring.
  • Dog tag (military style) — Rounded-rectangle identity tag with a chain hole at one end.
  • House-shaped keyring — House outline key fob with a ring hole in the roof.
  • Heart keyring — Heart-shaped key fob with a ring hole in one lobe.
  • Cable marker strip — Thin label strip with a slot at each end for cable ties.
  • Direction sign with arrow cut-out — Rectangular sign with a bold arrow cut through it, pointing left, right, up or down.
  • Chevron marking stencil — Stencil plate with a row of bridged chevrons for painting floor or road markings.
  • Arrow marking stencil — Stencil plate with a bridged arrow for painting direction markings.
  • Hanging sign with etched word — Rounded sign with two chain holes and a word etched in the middle (OPEN, CLOSED, WELCOME or your own).
  • Warning triangle with ! cut-out — Triangular warning sign with a bridged exclamation mark cut through it.
  • Exit sign with arrow — Rectangular sign with an arrow cut-out and the word EXIT etched beside it.
  • Distance marker plate — Tall post plate with a pointed top, fixing holes and an etched number.
  • Hazard stripe plate — Plate with diagonal hazard stripes etched across it, ready to paint, and corner fixings.
  • Round sign with bar cut-out — Round sign blank with a horizontal bar cut through the centre.
  • Projecting sign bracket — Straight projecting bracket with a diagonal brace, hanging holes along the arm and a wall plate with fixings.
  • Round plaque with border — Round plaque with an etched border ring and four countersink fixing holes inside it.
  • Sign post band blank — Flat band blank that wraps a round sign post, with slotted ears for the clamp bolts and sign fixing holes in the middle.
  • A-board leg — Tapered leg for a pavement A-board with a hinge hole at the top and a stay hole lower down.
  • Noticeboard header — Arched header panel for a noticeboard or village sign, with fixing holes along the base.
  • QR code plaque blank — Square plaque with an etched frame marking where a QR label or engraving goes, and four fixing holes.

Decorative and art (77)

  • Surprise me decorative panel — Generative decorative panel: every seed picks a pattern, feature size and border for you. Same seed, same panel, so you can order it again.
  • Mountain range wall art — Mountain range silhouette with a cut-out sun or moon, base strip and keyhole-style hanging holes. Seed changes the peaks.
  • Pine forest skyline — Row of pine trees of varying heights standing on a base strip, joined into one cut part. Seed changes the trees.
  • City skyline wall art — Generated city skyline of towers with lit windows cut out, on a base strip. Seed changes the buildings.
  • Mandala disc — Round mandala: rings of petal-shaped cut-outs around a centre, with a scalloped edge and hanging hole.
  • Sun face disc — Sun with wavy or straight rays round a disc, ring of cut-outs and a central eye; hang on a wall or fence.
  • Compass rose — Eight-point compass rose (long N/E/S/W points, shorter diagonals) with a centre hole and etched N marker.
  • Tree of life — Branching tree inside a ring, roots joined to the ring; every seed grows a different tree. One connected cut part.
  • Snowflake ornament — Six-fold snowflake made from rounded strokes with side branches, a hanging loop and seeded variation.
  • Star ornament — Five-point (or more) star with a matching star cut-out inside and a hanging hole near the top point.
  • Bauble ornament — Round bauble with a hanging cap and a cut-out pattern (stars, snow dots or rings).
  • Clock face — Clock dial for a standard quartz movement: centre spindle hole, 12 hour cut-outs (larger at 12, 3, 6, 9) and round or square outline.
  • Wall art blank with hangers — Plain rectangular or round art blank with two keyhole hanger slots at the back top, ready for your own engraving or paint.
  • Crescent moon — Crescent moon silhouette with an optional star cut-out and hanging hole.
  • Butterfly — Butterfly with four wings, a body and window cut-outs in the wings.
  • Leaf with veins — Pointed leaf with a stem and vein slots cut each side of the midrib.
  • Daisy flower — Daisy with long round-ended petals round a centre ring of seed holes.
  • Sunflower seed head — Disc with a sunflower spiral of seed holes (golden-angle pattern) and a petal edge.
  • Spirograph disc — Disc with a spirograph (hypotrochoid) curve etched on it and a hanging hole.
  • Fractal tree — Tree grown by repeated branching, standing on a base bar; branch angle and depth set the look.
  • Fern frond — Curving fern frond with paired leaflets that shorten towards the tip.
  • Koch snowflake — Fractal Koch snowflake outline: choose how many iterations of detail.
  • Sierpiński triangle — Triangle with the Sierpiński pattern of triangular holes at the chosen depth.
  • Sound wave wall art — Row of rounded bars of varying height (a waveform) joined along the centre line; the seed changes the wave.
  • Heartbeat line art — Heartbeat (ECG) trace inside a frame, cut as one piece.
  • Moon phases panel — Long plate with the phases of the moon cut out in a row: new, crescents, quarters, gibbous and full.
  • Solar system disc — Disc with the sun at the centre, etched orbit rings and the planets cut as round holes along them.
  • Constellation plaque (The Plough) — Plate with the seven stars of the Plough cut as star holes and joined by etched lines.
  • Dandelion clock — Dandelion clock on a curved stem: fine radiating seed stalks with tufted ends.
  • Tree-ring disc — Disc with irregular growth rings etched on it, like the end of a log; the seed changes the rings.
  • Topographic contour art — Rectangle with flowing topographic contour lines etched across it; the seed changes the landscape.
  • Ocean wave panel — Panel whose top edge rises into a curling wave crest.
  • Sitting cat — Simple sitting-cat silhouette with an eye cut-out (original design).
  • Bird on a branch — Small bird perched on a branch (original design).
  • Fish — Fish outline with a forked tail and an eye cut-out.
  • Whale tail — Whale tail (fluke) rising from the water line.
  • Hot-air balloon — Hot-air balloon with a basket, cut as one piece with window cut-outs.
  • Rocket — Cartoon rocket with fins and a porthole.
  • Sailing boat — Sailing boat with a mainsail and jib above the hull, cut as one piece.
  • Lighthouse — Lighthouse with a lantern room and banded window cut-outs.
  • Coffee cup — Coffee cup with a handle, saucer and steam window.
  • Acoustic guitar — Generic acoustic guitar outline with a sound hole.
  • Low-poly fox head — Faceted geometric fox head with eye cut-outs (original design).
  • Bicycle — Bicycle outline: two wheels and a frame joined into one piece.
  • Mountains in a circle — Ring frame with a mountain range, a rising sun and pine trees inside, cut as one piece.
  • Dragonfly — Dragonfly with four long wings and a slender body.
  • Bee — Round bee with striped body cut-outs and two wings.
  • Owl — Sitting owl with ear tufts and large eye cut-outs (original design).
  • Tree with heart crown — Tree whose crown is a large heart, with a trunk and roots.
  • Cactus — Saguaro cactus with two raised arms, in a pot.
  • Palm tree — Curved palm trunk with a crown of fronds.
  • Mushroom — Toadstool with a domed cap and spot cut-outs.
  • Feather — Feather with a quill and angled barb slots each side.
  • Flame — Flickering flame outline with an inner flame cut-out.
  • Rainbow — Rainbow arch with arc-slot bands and cloud feet.
  • Leaf wreath — Ring wreath of overlapping leaves with a hanging loop.
  • Snowman — Snowman of three balls with a top hat and button cut-outs.
  • Christmas tree — Christmas tree of stacked tiers with a star on top and bauble cut-outs.
  • Gingerbread figure — Gingerbread figure with button and eye cut-outs.
  • Pumpkin lantern — Ribbed pumpkin with a stalk and a carved face cut out.
  • Ghost — Friendly ghost with a wavy hem and eye cut-outs.
  • Bat — Flying bat with scalloped wings (original design).
  • Shooting star — Star with three trailing streaks.
  • Ringed planet — Planet with a tilted ring, cut as one solid silhouette.
  • Paper plane — Folded paper plane with a fold-line slot.
  • Cat face — Round cat face with pointed ears, eye and nose cut-outs and whisker slots.
  • Paw print — Single paw print: main pad and four toe pads joined by thin bridges so it cuts as one piece.
  • Music note — Pair of beamed quavers.
  • Moon and clouds — Round panel with a crescent moon and two drifting clouds, all joined to the ring.
  • Three pines — Rectangular panel with three stylised pine trees of different heights on a ground line.
  • Wave in a circle — Round panel with a curling wave and three wave lines, joined to the ring.
  • Leaf sprig — Tall panel with a curved stem and paired leaves, framed.
  • Sunrise over hills — Landscape panel with a rising sun and rays over two rolling hills.
  • Hearts garland — Long panel with a swag line and a row of hanging hearts.
  • Starburst ring — Round panel with a mid-century style starburst of long and short rays and dot ends.
  • Anchor and rope — Round nautical panel with an original anchor design and a curved rope line.
  • Clock hands pair — Hour and minute hands for a large wall clock, cut as one piece joined by a break-off tab, with spindle holes.

Garden and outdoor (62)

  • Gate hinge strap — Tapered gate strap with a rolled-eye or pin hole at the hinge end and countersink-size screw / bolt holes along the strap.
  • Hinge pin / hook plate — Post-side hinge plate: square or rectangular plate with a central pin hole for a welded hinge pin and four fixing holes.
  • Drop bolt keep — Keep / guide plate for a drop (cane) bolt: plate with a bolt hole near one end and two fixing holes.
  • Gate latch plate (thumb latch) — Gate latch keep: shaped plate with a hooked catch notch for the latch bar and fixing holes.
  • Hasp and staple pair — Hasp blank with a slot for the staple and a staple plate with a padlock loop hole; cut as one part with a sprue to snap apart, or choose either piece.
  • Fence panel bracket — Flat blank for a U-shaped fence panel bracket: centre web with post screw holes and two wings with panel holes, fold lines etched.
  • Gravel board clip — Small L-clip blank for fixing a gravel board to a post: etched fold line, two screw holes per leg.
  • Post cap / finial profile — Flat profile for a welded post top or railing finial: spear, fleur, acorn, ball, pyramid or round, on a base tab.
  • Gate stop / catch — Gate stop plate with a slotted face for a rubber buffer and two ground or wall fixing holes on a tab.
  • Gate wheel bracket — Side plate for a gate support wheel: axle hole at the bottom and gate-frame bolt holes or slots above for height adjustment.
  • Railing panel bracket — Lug that bolts a railing panel to a wall or post: tab with a slotted panel hole at one end and two wall holes.
  • Planter / tree ring segment — Curved planter or tree-surround edging segment: an arc strip that rolls into a ring, with joint plates holes at each end.
  • Raised bed corner plate — Flat corner bracket for raised beds or sleeper planters: folded down the etched line, with screw holes in both legs and a ground stake point.
  • Lawn edging strip with stakes — Steel landscape edging strip with ground stakes cut on the bottom edge and overlap holes at each end for joining lengths.
  • Fire pit side panel — Flat-pack fire pit side panel: tapered sides, decorative cut-outs, interlocking slots at each edge and air holes near the base.
  • Fire pit ring blank — Strip that rolls into a fire-pit ring: length set from the ring diameter, optional decorative cut-outs and air holes along the bottom.
  • BBQ / fire grill plate — Round or rectangular grill grate with parallel slots (stays in plate between), for fire pits and barbecues. Food-safe stainless recommended.
  • Bird box front plate — Front panel for a nest box with a round entrance hole (25 mm blue tit, 28 mm great tit, 32 mm sparrow are common sizes) and fixing holes.
  • Bird feeder hanger arm — Wall bracket arm with a curled hook end for bird feeders or hanging baskets, two wall fixing holes.
  • Plant label stake — Pointed garden marker stake with the plant name cut through (bridged stencil) in the head.
  • Garden silhouette stake — Lawn silhouette on a ground spike: hedgehog, robin, sitting cat or rabbit, cut as one piece.
  • Sundial plate and gnomon — Horizontal sundial gnomon cut to your latitude (style angle = latitude, about 51.5° for London), or the round dial plate with hour lines etched.
  • Boot scraper blade — Boot scraper blade with two ground spikes and a decorative top (plain, scroll ends or hedgehog bumps).
  • Hose hanger bracket — Wall-mounted hose hanger blank: back plate with fixing holes and a semicircular saddle to fold forward along the etched line.
  • Tree guard panel — Tall tree-guard side panel with vertical slots and pointed tops on the bars.
  • Plant support half-hoop — Flat half-hoop plant support with two legs to push into the soil.
  • Garden obelisk side panel — Tapered obelisk side with diamond openings for climbing plants.
  • Diamond trellis panel — Steel trellis panel: a diagonal lattice of diamond openings in a solid frame.
  • Hedgehog house entrance plate — Front plate for a hedgehog house with a 130 mm square-arched entrance, too small for most cats and foxes.
  • Bat box front — Front panel for a bat box with a narrow 15–20 mm entry slot at the bottom.
  • Arched fence topper — Fence-panel topper with a concave arched top edge and a row of circle cut-outs.
  • Planter foot bracket — L-shaped foot that bolts under a planter corner to lift it off the ground for drainage.
  • Log store end panel — End panel for a log store: rectangle with a big decorative circle cut-out and fixing holes.
  • Garden tool rack bar — Wall bar with open slots that hold spade and fork handles, and fixing holes between.
  • Hose guide stake — Flat stake with a rounded head and a large hole that guides the hose round the border corner.
  • Solar light ring stake — Stake with a flat ring on top to hold a solar light or jar lantern.
  • Garden sign on a stake — Sign blank with an integral pointed stake to push into the ground.
  • Lawn edging corner — Right-angle corner piece for steel lawn edging with stakes on both legs (fold along the etched line).
  • Chicken coop pop-hole door — Sliding pop-hole door with a lifting-cord hole and a finger slot.
  • Wind spinner blank — Disc with curved radial slits that are twisted after cutting to make a wind spinner.
  • Weather vane arrow — Weather-vane arrow with a feathered tail and a pivot hole at the balance point.
  • Weather vane compass cross — Fixed compass cross for a weather vane with the N, E, S and W letters etched near the arm ends.
  • Pergola knee brace plate — Curved knee-brace plate between a post and a beam, with bolt holes at both ends.
  • Compost bin side panel — Side panel for a compost bay with rows of air slots and fixing holes on the edges.
  • Log rack end frame — U-shaped end frame for a firewood rack, cut from one plate, with feet.
  • BBQ windshield panel — Tall side panel that stops wind blowing across a barbecue, with low vent slots and two locating tabs.
  • Plant pot trivet — Round trivet that lifts a pot clear of the paving, with drainage cut-outs.
  • Parasol base plate — Cross-shaped base plate for a parasol pole with a centre socket hole and holes for ground anchors or weights.
  • Shepherd's crook plant hook — Flat shepherd's crook stake for hanging baskets and lanterns, cut as one piece.
  • Hanging basket bracket — Hanging basket bracket with a curved arm, a hanging slot at the tip and a wall plate with two screw holes.
  • Gate closer bracket — Offset bracket for a gate closer spring, with a slotted post fixing and an eye for the spring end.
  • Raised bed stake plate — Pointed ground stake plate for holding raised bed sides, with screw holes in the top section.
  • Trellis wall spacer — Spacer plate that holds a trellis off the wall, with a wall screw hole and a trellis fixing slot.
  • Bird table tray blank — Flat tray blank with corner notches so the edges fold up, plus drainage holes.
  • Fence panel clip blank — Flat blank for a U-shaped fence panel clip, with fold lines etched and screw holes in the ears and back.
  • Garden arch side panel — Tall side panel for a garden arch with a ladder of square openings for climbers to grip, and ground spike tabs.
  • Plant pot stand ring — Ring for a plant pot stand with three leg tabs projecting outward.
  • Water butt stand side — Side panel for a water butt stand: a deep U with a curved top to cradle the butt, and floor tabs.
  • Soil sieve plate — Round perforated plate for a soil or compost riddle, with a plain rim for the frame.
  • Rotisserie fork — Flat rotisserie fork with prongs and a square hole that slides on the spit rod.
  • Stove door blank — Door blank for a stove or firebox with a window opening for the glass and hinge-pin and latch holes.
  • Fireplace fret — Low decorative front for an open fire grate: a stepped top with round and slot cut-outs.

Marine (34)

  • Mooring cleat base plate — Backing / base plate for a deck cleat: obround plate with the cleat bolt pair at your centres and optional extra hole pair. Not load rated: a cut blank only.
  • Pad eye plate (marine) — Flat pad-eye blank with a rounded head and pin hole, on a wide weld-on or bolt-down base. Not load rated: a cut blank only.
  • Anchor silhouette plate — Classic fisherman anchor silhouette (ring, stock, shank, curved arms with flukes), cut as one piece for signs and decor.
  • Ship's wheel decor — Ship's wheel silhouette: rim with spokes running through to turned handles and a centre hub hole.
  • Fairlead / rope guide plate — Flat fairlead plate: obround rope opening with radiused edges in a plate with four fixing holes.
  • Pontoon / jetty joint plate — Joint plate for pontoon or jetty frames: long plate with two groups of slotted holes so units can be aligned on the water.
  • Outboard transom pad — Transom reinforcement pad for small outboards: rectangle with radiused corners and four through-bolt holes at your clamp positions.
  • Mooring bollard base flange — Round base flange for a mooring bollard: centre socket and bolts on a PCD.
  • Horn cleat profile — Flat horn-cleat profile with two base bolt holes, for fabricating a welded cleat.
  • Bow-eye backing plate — Backing plate for a bow eye: radiused plate with the two bow-eye stud holes and a drain hole.
  • Rudder blade blank — Rudder blade with a raked leading edge, rounded tip and pintle-fitting holes along the top edge.
  • Tiller arm — Tapered tiller arm with a rudder-head bolt hole and an extension hole at the end.
  • Davit base plate — Square base plate for a boat or tender davit with a socket hole and four bolts.
  • Boat trailer roller bracket — Side plate for a boat-trailer keel roller: spindle hole at the top and U-bolt slots at the base.
  • Swim ladder bracket — Mounting bracket for a swim or boarding ladder: hooked top to hang the ladder and bolt holes for the transom.
  • Anchor chain stopper plate — Deck plate with a keyhole-shaped chain slot: the round end passes the chain, the narrow slot locks a link.
  • Porthole trim ring — Trim ring for a round porthole or portlight with screw holes round it.
  • Mooring ring plate — Wall or pontoon plate with a raised lug and a large ring hole for a mooring ring or shackle.
  • Boat chock / cradle pad — Cradle plate with a concave top curve to support a hull, and slots to adjust its height.
  • Fairlead plate — Deck plate with an obround rope lead slot and four countersink fixing holes.
  • Winch pad plate — Round winch mounting pad with bolt holes on a pitch circle and a centre drain hole.
  • Mast step plate — Mast step plate with a central slot for the heel fitting and bolt holes round the edge.
  • Chainplate — Tapered chainplate strap with a round top for the shackle pin and a line of hull bolt holes.
  • Bow roller cheek plate — Side cheek for an anchor bow roller, with the roller axle hole at the nose and a keep-pin hole behind it.
  • Boarding step plate — Step plate with rows of anti-slip slots and a fixing hole in each corner.
  • Hatch hinge plate — Hinge leaf with a rounded knuckle tab carrying the pin hole and countersink holes along the leaf.
  • Outboard bracket cheek — Cheek plate for an auxiliary outboard bracket: a pivot hole and a row of tilt-pin holes on an arc.
  • Jetty cleat backing plate — Elongated hexagonal backing plate for a jetty or pontoon cleat, with four bolt holes.
  • Kayak rack arm — Wall rack arm with a curved cradle for a kayak or paddleboard hull and two wall fixing holes.
  • Launching wheel bracket — Transom bracket for a dinghy launching wheel: a rounded leg with the axle hole and four transom bolt holes.
  • Anode mounting plate — Plate for bolting a sacrificial anode: two stud holes on the long axis and corner fixing holes.
  • Scupper drain plate — Round drain plate with radial slots and countersink fixing holes on the rim.
  • Rubbing strake joiner — Curved joiner plate for a steel rubbing strake or fender rail, with slotted holes for adjustment.
  • Davit arm plate — Curved davit arm cut from plate with a sheave pin hole at the tip and pivot holes at the base.

Workshop and jigs (53)

  • Table leg top plate — Top plate for welded table legs: square or round plate with countersink-size screw holes and the leg position etched.
  • Hairpin leg plate — Mounting plate for hairpin legs: rectangle angled-corner plate, rod positions etched, four screw holes.
  • Bed rail bracket — Hook-on bed rail bracket: plate with two angled hook slots that drop over pins, plus screw holes.
  • Workbench / machine foot — Foot plate for bench or machine legs: plate with a central levelling-screw hole, floor anchor holes and the leg outline etched.
  • Shelf bracket (profiled) — Flat shelf bracket in a choice of profiles (plain, curved, cut-out triangle, round window, industrial) with wall and shelf screw holes.
  • Coat hook blank — Flat coat hook to bend up at the etched line: back plate with two screw holes and a rounded hook tongue (single or double).
  • Coat rack rail — Rail plate with a row of fold-up hook tongues cut on three sides (bend each up at its etched line) and wall screw holes between.
  • Decorative corbel — Decorative corbel bracket with an ogee or stepped front curve and fixing holes in both legs.
  • Baluster infill panel — Balustrade infill panel cut from plate: vertical bars with a decorative band (circles, diamonds or waves) and fixing lugs top and bottom.
  • Welding fixture table plate — Modular welding table top or tile: 16 mm or 28 mm system holes on a 50 or 100 mm grid with an etched reference grid line every hole row.
  • Clamp / vice jaw plate — Replacement vice / clamp jaw plate with two countersink-size fixing holes at your centres and optional V-groove notch for round stock.
  • Welding magnet square plates — Side plates for a home-made welding magnet: arrow-shaped plate with 45° and 90° faces, lightening hole and two rivet / bolt holes for the magnet block.
  • Tensile test coupon — Flat dog-bone tensile coupon in typical BS EN ISO 6892-1 proportions: parallel gauge width b, gauge length, generous transition radius and grip ends. Machine edges after cutting for a valid test.
  • Bend test coupon — Rectangular bend-test strip in typical BS EN ISO 5173 proportions with an etched weld centre line and radiused long edges noted for dressing.
  • Weld procedure test plate — Pair of butt-weld test plates with an optional bevel allowance marked by an etch line and a stamp area etched in the corner.
  • Drill template plate — Drilling template with a rectangular or circular hole pattern, etched centre lines and a datum corner notch so it always goes on the right way round.
  • Tool hanger pegboard — Steel pegboard panel: a grid of 6 mm or 8 mm hook holes (25 or 38 mm pitch) with countersink-size fixing holes in the border.
  • Weld fillet / angle gauge — Pocket gauge with notches for common fillet leg sizes (3 to 12 mm) on one edge and 30/45/60/90 degree angle notches on another, sizes etched.
  • Radius gauge plate — Gauge plate with convex and concave radius checks on its edges, each etched with its size.
  • Wire / sheet gauge plate — Round gauge with slots round the edge for checking wire and sheet sizes, each slot etched with its size in mm.
  • Bolt and nut size gauge — Plate with clearance-size holes for M3 to M24 bolts, each etched with its size, for sorting bolts quickly.
  • Drill size gauge — Plate with holes from 1 to 13 mm in 0.5 mm steps for checking drill sizes, etched with each size.
  • Drill point angle gauge — Gauge with a 118° (or chosen) notch for checking drill point angles when sharpening, with a length scale etched along the edge.
  • Welding table stop (bench dog) — Flat stop for a welding-table hole grid: tab with a locating hole and a straight or V stop edge.
  • V-block plate — Plate with a 90° V notch to hold round bar for drilling or welding, plus a clamp slot.
  • Welding corner square — Right-angle welding square with a clamp window and a relief notch at the corner for the weld.
  • Mitre and angle template — Marking template with 45°, 30° and 60° edges for setting out mitres and angles.
  • Spanner rack — Wall rack with open slots that hold spanners by the jaw, and keyhole fixings.
  • Screwdriver rack — Strip with a row of graded holes for screwdrivers, files and pliers handles.
  • Sawhorse leg bracket — Flat bracket plate that joins a timber top rail to two splayed legs, with screw holes.
  • Grinder tool rest — Replacement tool rest for a bench grinder: platform with a slotted mounting tab.
  • Saw length stop — Flip-up length stop for a saw fence: plate with a clamp slot and a pivot hole.
  • Hose / cable reel bracket — Wall bracket with a curved saddle that hangs a coiled hose or cable, and keyhole fixings.
  • Gas cylinder wall bracket — Wall plate for securing gas cylinders with a chain: chain slots at each side and fixing holes.
  • Welding gear wall hook — Flat wall hook with a wide curved arm for helmets, leads and gauntlets.
  • Fire extinguisher wall plate — Wall plate with an extinguisher hook tab and a sign panel above.
  • Hole drilling jig strip — Drilling jig strip with a row of guide holes at equal pitch and a stop tab at one end.
  • Pegboard panel — Steel pegboard panel with a grid of peg holes and countersink fixing holes in the corners.
  • Vice jaw cover — Vice jaw plate with a V-groove notch along the top for holding round bar, and two screw holes.
  • Clamp rack — Wall rack for G and F clamps: a strip with open slots along the front and wall fixing holes.
  • Tap wrench blank — Bar-type tap wrench blank with a square drive hole in a round centre boss.
  • Chisel and file rack — Shelf strip with a row of round and slotted holes to hold chisels, files and punches.
  • Air line bracket — Wall bracket for an air filter-regulator unit with a centre port hole and fixings.
  • Grinding disc holder — Wall plate with a tab sized to the disc bore; the tab is bent out at 90 degrees on the etched line and the discs stack on it.
  • Steel rule blank — Steel rule blank with etched graduations every 10 mm and longer marks every 50 mm.
  • Centre finder plate — Centre finder for round bar: a 90 degree V notch with an etched line that bisects it. Sit the bar in the V and scribe along the line.
  • PCD marking template — Drilling template with a ring of holes on a pitch circle and a centre locating hole.
  • Tool hook strip — Wall strip with a row of upturned hooks for hanging tools and cables.
  • Sheet rack upright — Upright for a vertical sheet or offcut rack, with angled divider slots.
  • Bench grinder stand plate — Top plate for a bench grinder pedestal with slotted grinder feet holes and a central tube hole.
  • Plasma circle cutting guide — Trammel bar for cutting circles by hand: a torch ring hole and a row of pivot holes along the arm.
  • Pallet racking footplate — Footplate for a pallet racking upright: a plate with anchor holes either side of the upright and two bolt holes for the upright itself.
  • Racking row spacer — Flat row spacer that ties back-to-back racking frames together, with a pair of holes at each end.

Stairs and balustrades (32)

  • Cut (sawtooth) stair stringer — Plate stair stringer with the sawtooth profile cut for each tread: rise, going and number of risers, a waist depth below the nosings and floor / landing bearing cuts.
  • Flat stair stringer with cleat holes — Straight (closed) plate stringer at the stair pitch with bolt-hole pairs for each tread angle cleat, plumb top cut and level bottom cut.
  • Stair tread with nosing slots — Plate stair tread: rectangle with an etched contrasting nosing band line, drainage / anti-slip slots across the width and end cleat bolt holes.
  • Landing / quarter landing plate — Landing deck plate with optional corner cut for a newel, drainage holes on a grid and edge fixing holes.
  • Spiral stair tread — Wedge-shaped spiral stair tread: centre column ring, tread angle from treads per turn, outer radius and a baluster hole at the outer edge.
  • Baluster / post lug — Side-fix lug for welding to a post and bolting to the stringer face: tab with two slotted holes so the post can be plumbed.
  • Handrail end cap / wall plate — Round handrail wall rose or end cap with three or four countersink-size screw holes and the rail tube outline etched.
  • Glass balustrade base plate — Square or round base plate for a glass spigot or post: central spigot hole, four anchor holes and an optional drain notch.
  • Folded stair nosing blank — Flat blank for a folded stair nosing: tread leg with countersink holes and anti-slip slots, riser leg, fold line etched.
  • Ladder stile with rung holes — Flat ladder stile with round rung holes at 250–300 mm pitch (typical for fixed ladders) and wall bracket holes.
  • Winder tread — Tapered winder tread for a turning stair: narrow and wide ends with a straight nosing and fixing holes.
  • Kite winder tread — Kite-shaped winder for the corner of a quarter turn, with fixing holes near each edge.
  • Curved stringer segment — Flat arc band cut as a segment of a curved stringer or curved handrail plate (roll or form to suit).
  • Handrail wall bracket — Flat handrail bracket: round wall rose with three screw holes, cranked arm and a saddle to carry the rail.
  • Round balustrade post base — Round base plate for a balustrade post: post outline etched and four fixings on a PCD outside it.
  • Side-fix post plate — Side-fixing plate for a balustrade post on a slab edge or stringer: two vertical slots for level adjustment.
  • Newel cap plate — Square cap plate for a newel or box-section post, with a chamfered edge line etched and an optional finial hole.
  • Stair riser plate — Riser plate between treads: plain or with a row of perforations, and slotted fixings at each end.
  • Ladder safety-hoop segment — Flat C-shaped hoop for a fixed-ladder safety cage, with bolt lugs at each end and slots for the vertical straps.
  • Stair hanger strap — Hanger strap for a suspended stair or landing: long flat with a hole at the top and a slotted adjustment at the bottom.
  • Landing trimmer cleat — Cleat plate for a landing trimmer beam: tab with two bolts and a raked top corner.
  • Cat-ladder stand-off bracket — Stand-off bracket that holds a fixed ladder 200 mm or so off the wall: tapered arm, wall foot and stile holes.
  • Toe-board bracket — Small bracket that clamps a toe board to a handrail standard: curved saddle and two bolt holes.
  • Stair top hook plate — Head plate that hooks a stair stringer over the mezzanine edge beam, with bolt holes into the beam.
  • Stringer connection plate — Plate connecting a stair stringer to a landing trimmer, cut to the stringer pitch with bolt holes.
  • Tread support angle blank — Flat blank for a pressed tread support angle, with fold line etched and holes in both legs.
  • Half landing plate — L-shaped half landing plate with countersink fixing holes round the edge.
  • Handrail bend joiner — Curved joiner plate for a flat bar handrail at a change of direction, with countersink screw holes either side.
  • Spiral stair centre collar — Collar plate for a spiral stair tread, with the column hole and a projecting tread arm with fixing holes.
  • Loft ladder bracket — Pivot bracket for a loft ladder with a pivot hole, a stop slot and three fixing holes.
  • Fire escape tread — Perforated external stair tread with rows of drainage slots and end fixing holes.
  • Stair gate wall plate — Wall plate for screwing a stair gate cup to plaster or a newel, with two cup holes and four screw holes.

Brackets (43)

  • Angle bracket blank (folded) — Flat blank for a press-brake folded angle bracket: two legs with your hole counts, fold line etched at the leg length.
  • Z bracket blank (folded) — Flat blank for a Z (offset) bracket: three zones with fold lines etched and holes in both flanges.
  • U / channel bracket blank — Flat blank for a U (channel) bracket around a post or joist: base with fixing holes, two side legs with through-bolt holes, fold lines etched.
  • Pipe clamp half (saddle) — Flat two-bolt pipe clamp half: plate with a semicircular cut for the pipe OD and bolt holes either side (pair two for a full clamp).
  • Pipe hanger strap — Flat strap that rolls round a pipe for a hanger: length from the pipe OD, drop-rod holes in both ears.
  • Channel strut bracket — Flat plate fitting for 41 mm channel strut systems: hole pattern of 13.5 / 14 mm holes on 47.6 mm (1 7/8") pitch common to strut fittings.
  • Cable tray wall bracket — Cantilever arm for cable tray: L-shaped plate with tray slot holes along the arm and wall fixing slots in the upright.
  • Hanging sign bracket — Projecting sign bracket: wall plate, top bar with chain holes and a decorative scroll brace, cut as one piece.
  • Floating shelf bracket — Concealed floating-shelf back plate with countersink-size wall holes and an etched row where the support pins are welded.
  • Wall mount back plate — Rectangular wall mounting plate with a 4- or 6-hole wall fixing pattern, a central slot for cables and keyhole hangers for one-person fitting.
  • Heavy gusseted bracket set — Gusseted cantilever bracket profile (back, top and diagonal gusset in one plate) with a lightening cut-out and fixing holes.
  • Tee bracket (corner brace) — Flat T-shaped mending plate for timber or steel joints with a staggered screw pattern.
  • Mending / nail plate — Flat jointing plate with a dense staggered screw or nail hole field for timber repairs.
  • Timber post anchor / shoe — Flat cross-shaped blank for a U-shaped post shoe: square base with anchor holes, two side flaps with bolt holes, fold lines etched.
  • Restraint strap (lateral) — Flat lateral restraint strap: long strip with screw holes along its length and an etched bend line for the turn-down end.
  • Gallows bracket — Triangular gallows bracket cut as a frame: wall leg, shelf leg and diagonal brace with a triangular window.
  • Shelf bracket with lightening holes — Solid triangular shelf bracket with a curved hypotenuse and a row of graded lightening holes.
  • Scaffold-board shelf bracket — Flat bracket with an open U to drop a 225 × 38 mm scaffold board into, and wall holes.
  • Fascia gutter bracket — Flat fascia bracket for half-round gutter: curved cradle with a lip and two fascia screw holes.
  • Downpipe clip plate — Flat half-collar clip for a round downpipe with a projecting stand-off and wall hole.
  • Pipe saddle with ears — Flat pipe saddle: half-ring that goes over the pipe and two ears with screw holes.
  • Cable cleat plate — Two-piece cable cleat half: plate with a round cut for the cable and two clamp bolt holes.
  • Cantilever support arm — Tapered cantilever arm with a bolted wall plate end and a row of holes along the top for services.
  • Flat corner brace — Flat L-shaped corner brace with countersink-size screw holes on both legs.
  • Flat T plate — Flat T-shaped jointing plate with screw holes on all three arms.
  • Solar panel L-foot (flat) — Flat blank for a solar-rail L-foot: roof leg with two screw slots, rail leg with a slotted bolt hole, fold line etched.
  • Solar roof hook blank — Flat blank for a tiled-roof solar hook: rafter plate with screw slots and a cranked arm that passes under the tile.
  • Strut flat splice plate, 4-hole — Four-hole flat splice plate for 41 mm channel strut, holes at 47.6 mm pitch.
  • Strut flat tee plate — Flat tee fitting for joining three strut runs, holes on 47.6 mm pitch.
  • Strut flat cross plate — Flat cross fitting for four strut runs meeting at one point.
  • Strut flat L plate — Flat L fitting for a strut corner, three holes per leg position.
  • Strut 45° angle plate — Flat fitting that joins a strut run to a brace at 45°.
  • Strut square slotted washer — Square washer plate with a slotted hole for 41 mm channel strut.
  • Beam clamp plate — Clamp plate that grips a beam flange without drilling: stepped toe that bears on the flange and a bolt hole behind.
  • Pipe roller bracket — Side plate for a pipe roller support with the roller axle hole and two base fixing holes.
  • Radiator wall bracket — Flat radiator wall bracket with a hook for the radiator top bar and slotted wall fixings.
  • Speaker wall bracket — Wall plate for a speaker with a tilt arm, an arc slot for angle adjustment and four wall screw holes.
  • Projector ceiling plate — Ceiling plate for a projector or screen drop pole, with a centre pole hole and slotted ceiling fixings.
  • Satellite dish wall plate — Wall plate for a satellite dish or aerial mast, with a U-bolt hole pair and four wall fixings.
  • Awning arm bracket — Wall bracket for an awning arm, with a pivot boss hole and four wall fixings.
  • Bike wall hook plate — Wall plate with an upturned hook arm for hanging a bike by the wheel, and four screw holes.
  • Floor door stop plate — Floor plate for a door or gate stop with a raised buffer post hole and two countersink screw holes.
  • Wall tie plate — Lateral restraint wall tie plate: a long strap with a turned-down end marked and fixing holes along it.

Agricultural and farm (33)

  • Field gate latch plate — Latch keeper plate for a field gate: angled lead-in and a notch the latch drops into, with post fixings.
  • Cattle crush yoke bar — Flat yoke bar for a cattle crush head gate: long bar with a curved neck cut-out and pivot holes.
  • Bale spike mounting plate — Headstock plate for a bale spike: central spear boss hole, two stabiliser spike holes and frame bolt slots.
  • Loader attachment hitch plate — Side plate for a front-loader attachment bracket: top hook to engage the loader carriage and a lower locking-pin hole.
  • Pallet-fork frame end plate — End plate for a pallet-fork carriage: notches top and bottom for the fork bars and a frame bolt pattern.
  • Three-point headstock plate — Implement headstock plate with lower-link pin holes at Category 1 or 2 spacing and a top-link pin position.
  • Loader bucket wear plate — Bolt-on wear plate for a loader bucket floor: countersink-size bolt holes on a grid. Cut in Hardox for a long life.
  • Sprayer boom nozzle bracket — Small clamp bracket that holds a spray nozzle body on a square boom tube.
  • Drawbar eye plate — Flat drawbar eye: rounded end with the towing-eye hole and a tapered tongue with bolt holes.
  • Livestock gate hinge bracket — Hinge bracket for a livestock gate: post plate with an eye lug and bolt holes.
  • Water trough bracket — Hook-over bracket that hangs a water trough on a rail or post, with fixing holes.
  • Feeder ring segment — Curved panel segment for a round bale feeder: arc band with feeding windows between bars.
  • Auger hanger bearing plate — Hanger plate that carries an intermediate bearing in a screw-conveyor trough: U-shaped plate with the bearing bore.
  • Fence insulator bracket — Stand-off bracket that holds an electric-fence insulator off a post or wall.
  • Poultry feeder tray blank — Flat blank for a folded poultry feeding tray with anti-scratch bar slots and corner notches.
  • Top link bracket plate — Top link bracket cheek with a column of pin holes for setting the link angle and base bolt holes.
  • PTO guard bracket — Cranked flat bracket for holding a PTO shaft guard, with slotted adjustment holes.
  • Hay rack panel — Hay rack panel with tall feeding slots and a solid frame, for wall or field feeders.
  • Sheep hurdle clip — Figure-of-eight clip that links two hurdle uprights, with two tube holes.
  • Trough float cover — Cover plate for a water trough float valve, with a pipe hole and fixing holes.
  • Harrow tine clamp plate — Clamp plate for a spring tine, with a square-ish tine notch and two clamp bolt holes.
  • Mower blade blank — Rotary mower or topper blade blank with angled tips and a centre bolt hole.
  • Flail hammer blank — Flat flail hammer blank with a shackle eye and a wide cutting head.
  • Plough landside plate — Long plough landside wear plate with a chamfered heel and countersink bolt holes.
  • Gate slam plate — Slam plate for a field gate post with a rubber buffer hole and a padlock slot.
  • Log splitter wedge plate — Wedge plate for a log splitter ram, cut to a point with a weld-on base step.
  • Strainer post plate — Round bearing plate for a strainer post stay, with a centre rod hole.
  • Quad bike rack bracket — Bracket for mounting a sprayer or box on a quad bike rack, with U-bolt slots and an upright fixing tab.
  • Feed barrier yoke panel — Feed barrier panel with angled neck spaces so cattle feed side by side.
  • Bale feeder panel — Curved-top panel for a round bale ring feeder, with a row of feeding windows.
  • Stable door grille — Grille for the top half of a stable door: vertical bar openings under an arched top, with fixing holes round the frame.
  • Hive entrance reducer — Strip that narrows a beehive entrance, with entrance notches of different widths along one edge and pin holes.
  • Queen excluder — Slotted queen excluder sheet: rows of 4.2 mm slots that workers pass through and the queen cannot, inside a plain border.

Electrical (27)

  • Single-gang wall plate (86 × 86) — UK single-gang plate, 86 × 86 mm with two fixing holes at 60.3 mm centres: blank, switch aperture or grommet hole.
  • Double-gang wall plate (146 × 86) — UK double-gang plate, 146 × 86 mm with fixing holes at 120.6 mm centres and two apertures or blank.
  • Busbar link — Flat busbar link with a hole (or slot) at each end; cut in copper or aluminium.
  • Busbar angle link — L-shaped flat busbar link for turning a corner between bars, with a hole at each end.
  • Earth boss / bonding plate — Small earth bonding plate with a central stud hole and two fixing holes, etched with an earth mark.
  • Enclosure mounting backplate — Mounting backplate for an electrical enclosure: radiused corners, four slotted corner fixings and an optional DIN-rail hole grid.
  • Meter board plate — Steel meter board with a grid of fixing holes and grommet holes for meter tails.
  • Cable gland strip — Long gland strip with a row of holes for cable glands (M20, M25 or M32 clearances).
  • Lighting column door — Access door for a lighting column: obround panel with a lock hole and a hinge tab.
  • Junction box lid — Lid for a steel adaptable box: radiused corners and four corner screw holes (sizes common to 75–300 mm boxes).
  • DIN rail style strip — Flat 35 mm-wide rail strip with long slots at regular centres, as the blank for a folded top-hat rail.
  • Busbar support plate — Steel plate that carries busbar insulators: row of insulator holes on a chosen pitch and fixing slots.
  • Switch plate, triple — Three-gang switch faceplate with three rocker apertures and two fixing holes on 120.6 mm centres.
  • Socket faceplate, single — Single socket faceplate with a rectangular socket aperture between two fixing holes on 60.3 mm centres.
  • Socket faceplate, double — Twin socket faceplate with two apertures and fixing holes on 120.6 mm centres.
  • Blanking plate — Plain blanking plate for an unused one- or two-gang back box, with fixing holes at standard centres.
  • Multi-way earth bar — Earth bar with a row of conductor holes and two slotted mounting holes at the ends.
  • Neutral link bar — Neutral link bar with two staggered rows of terminal holes and end fixing holes.
  • Busbar flag terminal — Flag terminal for a busbar: a square tab with two bolt holes on a narrower neck with the busbar bolt hole.
  • Busbar tee link — Tee-shaped busbar link joining a run to a branch, with bolt holes in all three arms.
  • Cable ladder splice plate — Splice plate joining two cable ladder side rails, with two rows of slotted bolt holes.
  • Cable tray coupler — Flat coupler for perforated cable tray, with round holes for the tray and slots for adjustment.
  • EV charger post plate — Base plate for an EV charger post with a cable entry slot and four anchor holes.
  • Solar mid clamp blank — Mid clamp blank for PV panels: a T-head with a central bolt slot, before folding.
  • Solar end clamp blank — End clamp blank for PV panels: a stepped profile with a bolt slot.
  • Consumer unit blanking strip — Blanking strip for a DIN consumer unit or distribution board, with break-out tabs marked as etch lines.
  • Terminal block mounting plate — Mounting plate for a row of terminal blocks with slotted fixings and a cable tie slot row.

Heating and ventilation (26)

  • Rectangular duct flange — Flat flange frame for a rectangular duct: opening to the duct size and bolt holes round the frame.
  • Circular duct flange — Ring flange for a circular duct with an even bolt circle.
  • Spigot connection plate — Square plate with a round opening for a duct spigot and fixing holes, for connecting round duct to a plenum.
  • Damper blade — Round or rectangular damper blade with spindle holes on the centre line.
  • Louvre blade blank — Flat blank for a folded louvre blade with fixing tabs at each end and fold lines etched.
  • Fan mounting plate — Square fan plate with a round opening for the blades and the fan bolt holes on the diagonal.
  • Stove register plate — Chimney register (closure) plate for a wood burner: flue hole off-centre or central, inspection hatch and fixing holes round the edge.
  • Flue collar plate — Square or round trim plate that finishes round a flue pipe where it passes through a ceiling or wall.
  • Ventilation grille faceplate — Rectangular grille faceplate with a field of slots and countersink-size screw holes in the border.
  • Anti-vibration mount plate — Base plate for an anti-vibration mount: central stud hole and two slotted anchor holes.
  • Plant support bracket — Wall bracket for an air-conditioning condenser or small plant item: gusseted arm with mounting slots along the top.
  • Rain cap disc — Flat blank for a conical rain cap: disc with a sector removed so it closes into a shallow cone, plus strap holes.
  • Flat-oval duct flange — Flange ring for flat-oval ductwork with bolt holes evenly round the face.
  • Duct access door — Rounded access door panel for ductwork inspection, with handle slot and fixing holes round the edge.
  • Damper quadrant plate — Quadrant plate for a volume control damper: spindle hole and an arc slot for the locking wing nut.
  • Fire damper frame plate — Rectangular retaining frame for a fire damper sleeve, with fixing holes all round.
  • Louvre hood side cheek — Side cheek for a weather louvre hood: a sloped profile with fixing flange holes.
  • Square ceiling diffuser face — Square diffuser face with concentric rows of slots round a blank centre.
  • Linear slot diffuser face — Long face plate with parallel air slots for a linear slot diffuser.
  • Fan coil hanger bracket — Flat hanger bracket for a fan coil unit with a drop-rod slot and unit fixing holes.
  • Flue wall plate — Square wall plate with a round flue opening and four fixing holes.
  • Cowl spider bracket — Three-arm spider for supporting a chimney cowl or flue terminal, with a centre collar hole.
  • Duct hanger strap — Straight hanger strap with a line of fixing holes at a set pitch.
  • Transfer grille face — Door transfer grille face with angled slots, so it blocks a direct line of sight.
  • Cooker hood chimney bracket — Bracket for the chimney section of a cooker hood, with slotted wall fixings for adjustment.
  • Spiral duct support band — Flat band for a circular duct support clip, with a bolt eye at each end; length matches the duct circumference.

Furniture and interiors (50)

  • A-frame table leg — A-frame leg cut from plate: splayed sides, a top rail with fixing holes and a cross bar.
  • X-frame table leg — X-shaped leg with a top rail and a foot bar, cut as one frame.
  • U-frame table leg — Square-cornered U-frame leg cut from plate, with fixing holes in the top rail.
  • Trapezium frame leg — Closed trapezium frame leg, wider at the floor, with a window cut out of the middle.
  • Hourglass table leg — Waisted hourglass leg with top and foot rails, for café and bar tables.
  • Sled (skid) table leg — Closed rectangular frame leg with a floor runner that projects past the frame.
  • Bench leg with shelf notch — Frame leg for a hall bench with a notch to carry a lower shelf.
  • Pedestal table cross base — Cross-shaped base for a pedestal table with a centre column hole and levelling-foot holes at the arm ends.
  • Pedestal table round base — Round base disc for a pedestal table with column hole and countersink screw ring.
  • Bar stool footrest ring — Flat footrest ring for a bar stool with four tabs that weld to the legs.
  • Coffee table side panel — Solid side panel for a coffee or side table with a large round cut-out and fixing tabs.
  • Clothes rail end frame — End frame for a clothes rail: tall frame with a round notch at the top for the hanging rail and feet.
  • Bookend, plain — Plain bookend panel; fold the bottom edge (etched) or weld on a base tongue.
  • Bookend with arch window — Bookend with a round-topped window cut through it.
  • Bookend with circle window — Bookend with a large circle cut through it.
  • Double coat hook — Flat double hook: a long hook for coats and a short one above it for hats, with a back plate and screw holes.
  • Peg hook with ball end — Straight peg hook with a round ball end and a round back plate.
  • Key holder plate — Wall plate with a row of upturned hook tabs for keys and two screw holes.
  • Wine rack panel — Wine rack panel with a grid of bottle-neck or bottle-body holes; pair two panels with spacers.
  • Wall bottle holder — Wall plate with a projecting tongue and neck hole that holds one bottle horizontally.
  • Candle holder plate — Long plate with holes for tea lights or taper candles, with a scalloped edge.
  • Plant hanger bracket — Wall bracket for a hanging basket or plant: back plate and arm with a hook hole at the end.
  • Magazine rack side — Side panel for a magazine or log rack: U shape with a handle slot.
  • Towel / curtain pole bracket — Bracket with a round wall rose and an arm ending in a ring that carries a rail or pole.
  • Arched headboard panel — Arched-top headboard panel with a field of small round perforations and wall fixing holes.
  • Round mirror frame with hanger — Round frame for a mirror with an inner lip and a hanging tab at the top.
  • Under-desk cable tray blank — Flat blank for a folded under-desk cable tray with fixing tabs and cable slots.
  • Desk clamp plate — Clamp plate for a monitor arm or lamp: plate with a central post hole and screw holes, sits under the desk.
  • Flat-bar drawer pull — Flat-bar cabinet pull with two screw holes at standard centres; bend the ends after cutting.
  • Figure-8 desktop fastener — Figure-of-eight fastener that fixes a table top to its rail and allows the timber to move.
  • Table leg mounting plate — Square leg mounting plate with countersink-size corner screws and a centre hole for a threaded leg.
  • Twin-slot shelf upright — Flat shelf upright with two columns of bracket slots at a fixed pitch and screw holes between.
  • Stool seat plate — Round stool seat with a ring of drain holes and leg screw holes.
  • Kitchen trivet — Square or round trivet for hot pans with a lattice of cut-outs.
  • Fruit bowl blank — Round blank for dishing into a fruit bowl, with a decorative ring of leaf cut-outs.
  • Coaster — Round or square coaster with an etched pattern ring.
  • Napkin holder side — Side panel for a napkin holder with a wave top and a heart window.
  • Bed frame corner plate — Right-angled corner plate for a bed or box frame, with screw holes in both legs and a centre cut-away.
  • Table top fixing plate — Fixing plate for a wooden table top on a steel frame, with slotted screw holes so the top can move.
  • Shoe rack side panel — Side panel for a shoe rack with sloping shelf slots and floor feet.
  • Wine glass rack rail — Under-shelf rail with open keyhole slots that hold wine glasses by the foot.
  • Picture rail hook — Flat picture rail hook with a curled top that sits over the rail and a hanging hole at the bottom.
  • Plant stand top — Round top for a plant stand or side table with a decorative ring of slots and three leg fixing holes.
  • Slatted headboard panel — Headboard panel with vertical slatted openings and fixing holes for bolting to the bed frame.
  • Arched drawer pull — Flat arched pull handle with a finger opening and two screw holes on standard centres.
  • Chair back panel — Curved-top chair back panel with three vertical slots and fixing holes for the frame.
  • Tripod table base — Three-armed base plate for a pedestal side table with a column hole and foot holes.
  • Laptop stand side — Angled side plate for a laptop stand with a lip notch that stops the laptop sliding and a slot for the cross bar.
  • Toilet roll holder plate — Wall plate with a projecting arm for a toilet roll, with the arm tip turned up to keep the roll on, and two screw holes.
  • Mirror clip plate — Small clip that holds a frameless mirror or glass panel: a lip for the glass edge and a slotted screw hole.